Parts Sourcing · Updated 23 October 2026
OEM vs Aftermarket
Garage Door Spring Cost
We could not find a source that compares branded and supplier spring prices, so this page gives no "OEM premium". What we can cite is what springs cost at retail, by size. Here it is, and what to ask about the springs on your quote.
Published spring prices
| Spring | Seller | Price |
|---|---|---|
| Boxed torsion spring pair, 2 in ID, .225 wire, 23.5 inpair, with cones, winding bars and goggles; For 230 to 240 lb doors; rated at 10,000 cycles | DDM Garage Doors | $53.84 |
| DURA-LIFT DLTY225B torsion spring pair, 0.207 in x 2 in x 25 inpair, left and right wound, cones included; Weight capacity 91 lb; price shown for one store (Ellsworth, ME), and Home Depot says local prices may vary | The Home Depot | $79.41 |
| Residential torsion springs for 7 ft doorsone spring; 112 ready-listed springs, 0.207 to 0.2625 wire | DDM Garage Doors | $35.38 to $87.91 |
| Torsion springsone spring, with cables and winding bars; 272 listings, 0.192 to 0.283 wire | DIY Garage Door Parts | $75.25 to $157.94 |
| Extension springs for 7 ft doors, 100 to 200 lbone spring; Extension springs are replaced in pairs | DIY Garage Door Parts | $29.92 to $72.90 |
| Wayne Dalton TorqueMaster springsone spring; 84 listings | DDM Garage Doors | $60.00 to $70.00 |
| Commercial torsion springsone spring; Three sizes, 3.75 to 5.25 in ID | DDM Garage Doors | $172.49 to $332.35 |
Retail prices read 13 and 14 October 2026; the Home Depot price is for one store, and Home Depot says local prices may vary. These are what the public pays at retail; the parts line on an installer's quote is set by that installer, so ask for it separately.
How we price this: Our ranges are estimates built from published inputs, not quotes: retail spring prices, the service-call and hourly rates in Yelp's cost guide, and job times from HomeAdvisor and Yelp. Low ends are rounded down and high ends up to the nearest $5. Sources, read 13 October 2026: DDM Garage Doors, Yelp cost guide, HomeAdvisor and DIY Garage Door Parts. HomeAdvisor and Angi are both owned by Angi Inc., which pays this site a commission for quote requests. (Angi Inc. 2025 Form 10-K)
Show the arithmetic
- One Wayne Dalton TorqueMaster spring (per spring; estimate from stated inputs; includes parts, labor, service call): $135 to $270. parts $60.00 to $70.00, plus labor $75 to $200 (a $75 to $100 service call covering the first hour, plus up to one more hour at $100): $135.00 to $270.00, rounded out to the nearest $5.
- Two Wayne Dalton TorqueMaster springs (pair; estimate from stated inputs; includes parts, labor, service call): $195 to $340. parts 2 x $60.00 to 2 x $70.00, plus labor $75 to $200 (a $75 to $100 service call covering the first hour, plus up to one more hour at $100): $195.00 to $340.00, rounded out to the nearest $5.
- Pair of torsion springs replaced (pair; estimate from stated inputs; includes parts, labor, service call): $145 to $520. parts 2 x $35.38 to 2 x $157.94, plus labor $75 to $200 (a $75 to $100 service call covering the first hour, plus up to one more hour at $100): $145.76 to $515.88, rounded out to the nearest $5.
Parts are priced at what the two suppliers charge the public. Installers buy for less and many mark parts up, and neither figure is published, so a quote's parts line can be higher than ours.
Wage check: The BLS puts the median mechanical door repairer (the occupation that includes garage door mechanics) at $26.79 an hour (May 2025). Wages are 70.0% of private-industry employer costs (June 2026), so that technician costs an employer about $38.27 an hour before the van, insurance, overhead and profit. Yelp's $40 to $100 hourly rate sits at or above that cost, which is what a billed rate should do. (BLS OEWS, 49-9011 Mechanical Door Repairers; BLS Employer Costs for Employee Compensation)
What decides the spring, and the price
A standard torsion spring is specified by its wire size, inside diameter, length and wind (left or right), and it is chosen to balance the door's weight. That is how suppliers list them: DDM Garage Doors sells 112 ready-listed springs for 7 ft doors, each titled by the weight it lifts and its size, not by door brand. DASMA Technical Data Sheet 190 warns that a spring that does not meet the door's counterbalance requirement can shorten its life and create a safety issue, which is why the size on a quote matters more than the name on the box.
Installed, a standard torsion pair is $145 to $520 on our estimate. The spring is the smaller part of that bill: $35.38 to $157.94 each at retail, against $75 to $200 for one visit of labor.
Wayne Dalton TorqueMaster
TorqueMaster is Wayne Dalton's enclosed system: the springs sit inside the tube above the door, and it takes its own springs. They are sold to the public: DDM Garage Doors lists 84 TorqueMaster springs at $60.00 to $70.00 each. On our estimate one is $135 to $270 installed and two $195 to $340. Not every company works on TorqueMaster doors, so say it is one when you call.
What to ask before booking
- What springs are you fitting: wire size, inside diameter, length, wind and cycle rating?
- Who makes them, and what is the warranty on the springs and on the labor, in writing?
- Is the parts line separate from labor and the service call, so I can compare quotes?
- If you recommend a particular brand, why, and what would the alternative cost?
- Is my door still under the maker's warranty, and does that affect which parts you can fit?
Related cost guides on this site
Frequently Asked
How much more does an OEM garage door spring cost?
We could not find a like-for-like price comparison of branded and supplier springs to cite, so we give no OEM premium. The retail prices we can cite are from parts suppliers and home centres, which list springs by wire size, inside diameter and length rather than by door brand: DDM Garage Doors sells standard torsion springs at $35.38 to $157.94 each. Ask your installer what springs they are fitting and what an alternative would cost, as separate lines.
How much does a Wayne Dalton TorqueMaster spring cost?
DDM Garage Doors lists 84 TorqueMaster springs at $60.00 to $70.00 each. Installed, on our estimate, one is $135 to $270 and two $195 to $340, parts, labor and service call included.
Does the spring have to match my door's brand?
It has to match the door: its weight, the drums and the spring system. A standard torsion spring is specified by wire size, inside diameter, length and wind, and a correctly sized spring from any supplier does the same job. Enclosed systems such as Wayne Dalton's TorqueMaster take their own springs. If your door is still under a maker's warranty, read the terms before any repair.